1 Introduction
Chelating bis-N-heterocyclic carbene (NHC) complexes followed as early developments after the introduction of the NHC functionality in the coordination chemistry, which gained momentum with the isolation of ‘bottleable’ NHCs by Arduengo [1]. Bis-imidazolium salts linked by alkylene spacers served as precursors to the corresponding NHCs and proved the reagents of choice as in situ sources of the NHC ligands leading to the synthesis of Pd complexes [2].
Since then, chelating dicarbene ligands (Scheme 1) have been studied mainly on Pd and Pt centres due to the emerging potential of the corresponding complexes in homogeneous catalysis (cross coupling, copolymerisation, carbonylation, C–H activation, CO2 activation), [3] stabilisation of high oxidation states [4] and, more recently, photophysical applications [5]. Other metals have not been studied as extensively. Early work on Ni demonstrated the potential of Ni-NHC complexes in catalysis [6], and on Cr the stabilisation of organometallics of relevance to alkene polymerisation and oligomerisation [7]. In most cases, the commonly used ligand with a methylene spacer between the heterocyclic donors (Scheme 1 A–C) is not being isolated, but introduced to the metal centre by the reaction with metal precursors coordinated to an internal base (e.g. acetate, acac, etc.), or by deprotonating the di-imidazolium precursors in situ with an external base (NaOAc, Et3N) in the presence of a suitable metal precursor.
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/sc1.jpg)
Attempts to isolate the free di-NHC ligand have been reported for type A ligands (R = Bu,t [6a] benzyl [6b]). In addition, the ligand of type C (R = DiPP) has been prepared by deprotonation of the corresponding imidazolium salt with KN(SiMe3)2 in THF at room temperature [7]. This method, albeit attractive, proved in our hands problematic leading to intensely colored and spectroscopically impure materials, which we were unable to purify by common methods. On the other hand, the advantage of the product stoichiometry control provided by the bulky ligands of type C (i.e. formation of complexes with ligand-to-metal stoichiometry 1:1 rather 2:1, the latter being common with NHC ligands of type A), prompted us to reinvestigate and expand the synthetic methodology to access the aforementioned ligands of type C. In this paper we describe an improved synthesis of ligands Lmes and LDiPP in synthetically useful quantities and high purity. We also provide some examples of novel transition metal organometalllics that demonstrate some advantages of using the free ligands in synthesis by simple substitution reactions. A summary of the chemical transformations is given in Scheme 2.
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/sc2.jpg)
Synthetic transformations leading to the ligands, derivatives and complexes described in this paper. Reagents: (i) S8, Se or Te; (ii) [Pd(tmeda)Me2] (M = Pd); [Pt(μ-SMe2)Me2]2 (M = Pt); (iii) [Ir(1,5-COD)(μ-Cl)]2/KPF6; (iv) [NiBr2(dme)]; (v) Na(Hg)/CO.
2 Results and discussion
2.1 Synthesis of ligands and derivatives
The bis-imidazolium salts (LmesH2)Br2 and (LDiPPH2)Br2 were prepared by adaptation of established literature procedures [3d,7,8]. Analytically pure, colourless solids were obtained after washing the precipitated products that were formed by the quaternisation of the imidazoles with CH2Br2 in xylenes, with small amounts of acetone. For structural characterisation of the (LDiPPH2)2+, (LDiPPH2)Br2 was converted to the triflate salt and crystallised from CH2Cl2/petrol. The structure of the dication in (LDiPPH2)(OTf)2 determined crystallographically is depicted in Fig. 1. It is worth commenting on some differences observed in the structure of the (LDiPPH2)(OTf)2 and the known (LDiPPH2)Br2·H2O [7]. The vectors of the two C–H imidazolium bonds in the former are pointing to the same direction; this is certainly due to the formation of H-bonding between these C–H hydrogen atoms with one oxygen atom of the triflate anion. The interaction may also influence the angle between the two heterocycles (75.20°) and the N2-C16-N2′ angles. The vectors of the two C–H imidazolium bonds in the (LDiPPH2)Br2·H2O are pointing to opposite directions, being involved in H-bonding with different Br− in the lattice. Lastly, the situation in (LmesH2)Br2 [9] is analogous with that in the triflate salt mentioned above (i.e. imidazolium C–H vectors are pointing to the same direction and H-bonding with the same Br−) even though the N-C-N angle at the bridging C atom is ca. 112° (cf. ca. 110° in (LDiPPH2)(OTf)2). Therefore, it appears that the relative orientations of the C–H bonds, the interplanar angle between the imidazole heterocycles and the angle at the bridging C atom are dependent on crystal packing and H-bonding interactions between the imidazolium hydrogens and the anion(s).
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr1.jpg)
Representation of the dication in the structure of (LDiPPH2)(OTf)2; ellipsoids are at 30% probability level. Only one disordered position of one Pri groups of one DiPP ring is shown for clarity. Selected bond lengths (Å) and angles (deg): C13–N1 1.332(6), C13–N2 1.329(7), N2–C13–N1 108.4(4), N2–C16–N2′ 110.1(6), N2–C13–N1 108.4(4).
Prior to the deprotonation reactions described below, the imidazolium salts were dried azeotropically with toluene.
In order to access the free Lmes and LDiPP, the conditions of deprotonation described previously [7] have been modified to suppress product decomposition which is noticeable above –20 °C by the intense brown coloration of the reaction mixture. The decomposition slowed down if the deprotonation was carried out in diethyl ether and the product when dissolved or suspended was maintained below –20 °C. However, after isolation of the product as a solid, it was stable for longer periods (at least 0.5 h) at room temperature under inert atmosphere without appreciable visual or spectroscopic (1H-NMR) change. We were unable to establish the nature of the colored decomposition product. The off-white to yellow LDiPP and Lmes were characterised by NMR spectroscopic methods (1H and 13C{1H}). The spectra support a symmetrical structure in solution, while the CNHC in the 13C{1H} spectrum for both ligands appear at ca. δ 218. Interestingly, X-ray quality crystals of Lmes were obtained and used for structural determination by crystallography. Due to the poor crystal quality as evidenced from the observation of low diffraction angles, the data set was finally collected at the Daresbury synchrotron facility, and was suitable to establish the unit cell contents and atom connectivity and extract metrical data with reasonable accuracy. A diagram of the molecule is shown in Fig. 2.
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr2.jpg)
Representation of the structure of Lmes; ellipsoids are at 30% probability level. Selected bond lengths (Å) and angles (deg): N1–C10 1.3702(12), N2–C10 1.3617(12), N3–C14 1.3674(12), N4–C14 1.3646(13), N2–C10–N1 101.56(8), N3–C13–N2 112.02(8), N4–C14–N3 101.50(8).
The molecule adopts a conformation where the lone pairs at CNHC are pointing towards opposite directions, with an interplanar angle between the heterocycles of 77.85°. In addition, there is a reduction of the size of the angles at the CNHC compared to the corresponding angles in the imidazolium salts.
Derivatisation of the NHCs by the reaction with chalcogens has been used as a chemical diagnostic method for their transient presence and characterisation of free NHCs and their indirect structural identification. The most commonly employed chalcogen for this purpose is S8 leading to air stable thioureas. Less stable selenoureas and telluroureas are expected from the reaction with Se and Te, respectively. Taking advantage of this methodology in order to confirm the successful preparation of the free NHC ligands as detailed above, we reacted the isolated LDiPP with S8, Se and Te and obtained the corresponding ureas that were characterised spectroscopically and analytically. In addition, the structure of the telluro-urea LDiPPTe2 was determined crystallographically and is shown in Fig. 3. It constitutes a rare example of structurally characterised compound of this type [10].
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr3.jpg)
Representation of the structure of LDiPPTe2; ellipsoids are at 30% probability level. One molecule of crystallisation solvent C6D6 in the asymmetric unit is omitted for clarity. Selected bond lengths (Å) and angles (deg): C13–N1 1.370(6), C13–N2 1.371(6), C13–Te1 2.065(5), C17–N4 1.353(6), C17–N3 1.373(6), C17–Te2 2.073(5), N2–C13–N1 108.4(4), N2–C16–N3 116.4(3), N4–C17–N3 105.3(4).
The heterocyclic rings arrange at a dihedral angle of 45.12°, while the CTe vectors have an antiorientation. The CTe–N bond lengths are virtually identical with the corresponding CNHC–N in the free NHC, however the values of the endocyclic angle at the CTe are significantly larger than the corresponding at the CNHC, which may indicate a varying degree of π-interaction of the CTe and the adjacent N atoms.
2.2 Transition metal complexes
The availability of the free chelating bulky Lmes and LDiPP ligands prompted us to carry out some preliminary explorations of their scope by means of the synthesis of representative examples of transition metal complexes. It is known that the coordination of the free chelating dicarbene ligands reported previously [6,7] with group 10 metal centres (Ni2+, Pd2+) leads to homoleptic complexes of ligand-to-metal stoichiometry 2:1 due to the kinetic control of the initial complexation reaction and the fact that strong metal-NHC bonds in combination with the chelate effect slow down ligand dissociation and redistribution. Therefore, the chemoselectivity of the LDiPP and Lmes towards formation of complexes of 1:1 stoichiometry is a potentially attractive feature to consider.
Reactions of LDiPP with one equiv. of [Pd(tmeda)Me2] (tmeda is N, N, N′, N-tetramethylethylenediamine) or 0.5 equiv. of [Pt(μ-SMe2)Me2]2 resulted to the clean formation of the complexes [Pd(LDiPP)Me2] and [Pt(LDiPP)Me2], respectively. The complexes were characterised analytically, and by NMR spectroscopy. The 1H-NMR spectrum indicates highly symmetric structures in solution as evidenced by the presence of two doublets and one septet for the isopropyl groups of the DiPP substituents. However, the solid-state structures determined crystallographically (see Figs. 4 and 5 for complexes 1 and 2, respectively) indicate lower symmetry, originating from the puckered six membered chelating ring.
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr4.jpg)
Representation of the structure of 1; ellipsoids are at 30% probability level. One disordered THF molecule in the asymmetric unit is omitted for clarity. Selected bond lengths (Å) and angles (deg): C1–N1 1.361(3), C1–N4 1.361(3), C1–Pd1 2.071(2), C3–Pd1 2.065(2), C3–N3 1.375(3), C3–N2 1.372(3), C32–Pd1 2.069(2), C33–Pd1 2.074(2), C3–Pd1–C1 87.95(8), C32–Pd1–C1 94.04(9), C32–Pd1–C33 85.33(9), C3–Pd1–C33 92.75(9).
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr5.jpg)
Representation of the structure of 2; ellipsoids are at 30% probability level. One THF molecule in the asymmetric unit is omitted for clarity. Selected bond lengths (Å) and angles (deg): C1–Pt1 2.088(5), C2–Pt1 2.088(5), C3–Pt1 2.037(5), C4–Pt1 2.020(5), C3–N3 1.367(6), N4–C3 1.372(6), C4–N1 1.390(6), N2–C4 1.380(5), N3–C3–N4 102.3(4), C2–Pt1–C1 85.35(19), N2–C4–N1 100.4(4), C3–Pt1–C1 93.43(18), C4–Pt1–C3 88.15(17), C4–Pt1–C2 93.14(18).
The bond lengths and angles are similar to those previously observed for analogous species [3a,11]. However, it is interesting to comment on a trend of M-CH3 and M-CNHC bond lengths in these very similar species: in the Pd complex 1, the lengths of the two types of bonds are almost equal (within the measured e.s.d.s) but in the Pt complex 2 the CNHC bonds are significantly shorter than the Pt-CH3 bonds. This may imply a different balance of σ- and π-bond components for the two types of bonds but detailed understanding is not yet possible. The only other Pt dimethyl complex with a ligand of type A (R = But) (Scheme 1) was recently reported [3a] in conjunction with its reactivity toward CO2; it was prepared by transmetallation from Ag to Pt. Bis-alkynyl complexes with a ligand of type A (R = C6H11) were studied in relation to their luminescence properties; they were prepared by direct metallation of the imidazolium salts with PtCl2 in the presence of NaOAc, followed by reaction of the halides with alkynes [5b]. Pd dimethyl complexes with Lmes have been previously prepared by in situ deprotonation of the salt (LmesH2)Br2 [3c] but not structurally characterised.
Reactions of LDiPP with 0.5 equiv. of [Ir(1,5-COD)(μ-Cl)]2 followed by anion exchange with KPF6 gave complex 3, which was characterised analytically, spectroscopically and crystallographically. In contrast to 1 and 2, the 1H NMR spectrum of 3 showed a non-symmetrical structure in solution as supported by the presence of four doublets and two septets for the isopropyl groups of the DiPP substituent. The non-symmetrical structure is also seen in the solid state as depicted in the diagram of the cation (Fig. 6) obtained from a crystal structure determination of 3.
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr6.jpg)
Representation of the structure of the cation in 3; ellipsoids are at 30% probability level. The anion (PF6)− and one THF molecule in the asymmetric unit are omitted for clarity. Selected bond lengths (Å) and angles (deg): C1–N2 1.345(7), C1–N1 1.379(7), C1–Ir1 2.076(5), C5–N3 1.339(7), C5–Ir1 2.058(6), C32–Ir1 2.191(6), C35–Ir1 2.215(6), C5–N4 1.378(7), C39–Ir1 2.209(6), N2–C1–N1 103.1(5), N3–C5–N4 103.5(5), C5–Ir1–C1 87.4(2).
The Ir centre adopts a distorted square planar geometry with virtually equal Ir–CNHC bonds within the measured e.s.d.s. The Ir–CCOD bond lengths fall into the range 2.165–2.216 Å and there is elongation of the coordinated olefinic bonds due to increased back-bonding from the electron rich metal due to the strong σ-donor ability of the coordinated NHCs. Complex 3 is the first example of IrI centre with ligands of the type shown in Scheme 1. Two examples of IrIII complexes with ligands of type A (R = Pri) have been obtained by the deprotonation of the corresponding bis-imidazolium salts with NaOAc or Et3N in the presence of [Ir(1,5-COD)(μ-Cl)]2 and [Cp*IrCl(μ-Cl)]2, in processes that may also involve C–H activation of the C2-H by the Ir center [12]. The catalytic activity of 3 is currently under investigation.
Finally, LDiPP was reacted with [NiBr2(dme)] in THF to afford the pink, paramagnetic tetrahedral complex 4, which was characterised by analytical and X-ray diffraction methods. The analytical data support a ligand-to-metal stoichiometry of 1:1. Unfortunately, the crystals obtained were invariably of small size, which in combination with the low solubility of 4 in inert solvents (a fact that eliminates controlled recrystallisations, see Experimental Section) hampered an accurate crystal structure determination. Eventually a data set obtained at the synchrotron X-ray facility, Daresbury, UK, was adequate for solution and satisfactory refinement of the model, which established unequivocally the atom connectivity in the complex and its essential geometrical and metrical features (Fig. 7).
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr7.jpg)
Representation of the structure of 4; ellipsoids are at 30% probability level. Selected bond lengths (Å) and angles (deg): Ni1–Br1 2.3501(10), Ni1–Br2 2.4009(10), C13–Ni1 1.976(7), C17–Ni1 = 1.975(6), N2–C13–N1 102.8(5), Br1–Ni1–Br2 123.00(4), C13–Ni1–Br2 102.75(17), C17–Ni1–Br2 96.92(16), C13–Ni1–Br1 115.20(18), C17–Ni1–C13 91.5(2).
The Ni centre is in a distorted tetrahedral geometry with wide Br–Ni–Br (123.00(4)°) and relatively small CNHC–Ni–CNHC (91.5(2)°) angles. The Ni–CNHC bonds fall in the long end of the observed range (average 1.90 Å, range 1.85–2.08 Å).
In view of the thermal and air sensitivity of LDiPP, which may limit its use for the synthesis of the interesting complex 4, we developed a methodology based on the in situ deprotonation of the imidazolium salt (LDiPPH)2Br2 with KN(SiMe3)2. However, the low solubility of 4 in the reaction medium resulted in its contamination with KBr, the salt metathesis product from the deprotonation. Unexpectedly, purification of the mixture of 4 with KBr could be carried out by quick washing with degassed water on a glass sinter followed by quick drying giving analytically pure 4. The observed selectivity for the formation of the complex of 1:1 metal-to-ligand stoichiometry as observed with 4 should be contrasted with the other NiII complexes with ligands of type A in Scheme 1, where the preferred products are square planar species of 1:2 metal-to-ligand stoichiometry and may be ascribed to the steric requirements of LDiPP.
Preliminary reactivity studies showed that 4 could be reduced in the presence of CO to the [Ni(LDiPP)(CO)2], a Ni0 complex, which was structurally characterised (Fig. 8).
![](/chimie/article/CRCHIM_2013__16_6_557_0/jpg/src/tex/figures/gr8.jpg)
Representation of the structure of 5; ellipsoids are at 30% probability level. Selected bond lengths (Å) and angles (deg): C17–Ni1 1.955(2), C13–Ni1 1.957(2), C32–Ni1 1.759(3), C33–O2 1.158(3), C32–O1 1.159(3), C33–Ni1 1.764(2), C32–Ni1–C33 111.16(11), C32–Ni1–C17 112.93(10), C33–Ni1–C17 113.18(10), C32–Ni1–C13 113.68(10), C33–Ni1–C13 112.65(10), C17–Ni1–C13 92.06(9).
Here too, the metal is in a tetrahedral environment with CNHC–Ni–CNHC angle of 92.06(9)° very similar to the one observed in 4. This value may relate to the LDiPP ligand natural bite angle [13]. The Ni–CNHC bond lengths are marginally shorter than in 4 while the Ni–CCO are shorter than the Ni–CNHC bonds indicating a good degree of π-back-bonding.
3 Conclusions
A method for the synthesis of free 1,1′-methylene-bis-(3-aryl-imidazol-2-ylidene) ligands of high purity and in synthetically useful quantities will provide alternative or complementary routes for the synthesis of organometallic complexes that are sensitive to strong bases or the oxidising conditions of transmetallation from silver. This idea has been exemplified in this work by the synthesis of some novel organometallics of group 10 and Ir metals that were either not previously accessible or via multistep synthetic schemes. We expect that this development will open the way for the more widespread use of 1,1′-methylene-bis-(3-aryl-imidazol-2-ylidene) ligands across the Periodic Table.
4 Experimental
4.1 General
All manipulations were performed under nitrogen in a MBraun glovebox or using standard Schlenk techniques, unless stated otherwise. Solvents were dried using standard methods and distilled under nitrogen prior use. The light petrol used throughout had a b.p. of 40 to 60 °C. The starting materials were obtained from commercial sources or prepared by modification of the literature procedures as follows: crude, usually colored bis-imidazolium (LmesH2)Br2 [8] and (LDiPPH2)Br2 [7], were washed with minimum amount of acetone to afford colorless powders that were dried under vacuum and finally azeotropically with toluene. The salt (LDiPPH2)(OTf)2 that was prepared to facilitate crystallographic characterisation of the bis-imidazolium cation, was obtained by anion exchange from (LDiPPH2)Br2, with NaO3SCF3 in CH2Cl2 and crystallised from CH2Cl2/petrol; [Pd(tmeda)Me2] [14] and [PtMe2(μ-SMe2)]2[15] were prepared according to literature methods.
Elemental analyses were carried out by the London Metropolitan University microanalytical laboratory. NMR data were recorded on Bruker AV-300 and DPX-400 spectrometers, operating at 300 and 400 MHz (1H), respectively. The spectra were referenced internally using the signal from the residual protio-solvent (1H) or the signals of the solvent (13C).
4.1.1 1,1′-methylene-bis-(3-diisopropylphenyl-imidazol-2-ylidene) LDiPP
(LDiPPH2)Br2 (2.50 g, 4.00 mmol) was weighed out into a Schlenk and suspended in diethyl ether (30 ml). In a separate Schlenk, KN(SiMe3)2 (1.74 g, 8.70 mmol) was dissolved in diethyl ether (20 ml). The solution of KN(SiMe3)2 was cooled to -78 °C and added portionwise with efficient stirring to the suspension of the salt at the same temperature, the suspension turning cream upon full addition. The mixture was stirred at -78 °C for 1 h and allowed to warm to –30 °C slowly over 2 h and stirred at this temperature for 30 min. At this point a light yellow suspension is formed. The reaction mixture was filtered through Celite into a cold (–30 °C) receiver flask. The precipitate was washed with cooled (–20 °C) diethyl ether (4 × 50 ml). The solvent was removed under reduced pressure to give a lemon yellow solid, which was spectroscopically pure. Yield: 1.46 g, 78%. NMR (C6D6): 1H, δH 1.10, 1.30 (2 × 6H, d, CH(CH3)2, J = 7.32 Hz), 2.80 (2H, septet, CH(CH3)2, J = 7.32 Hz), 6.30 (2H, s, CH2 bridge), 6.50 (2H, s, 5-imidazol-2-ylidene), 7.20 (2H, s, backbone imidazol-2-ylidene), 7.20 (4H, d, aromatic DiPP, J = 7.32), 7.30 (2H, t, aromatic DiPP, J = 7.32). 13C{1H}: δC, 23.7, 24.5 (iPr CH3), 28.5 (iPr C(CH3)2), 65.6 (-CH2-), 118.1, 122.8 (4,5-imidazol-2-ylidene), 128.3, 128.9, 132.0, 146.2 (aromatic), 218.9 (imidazol-2-ylidene). The solid can be stored at –35 °C under nitrogen without decomposition.
4.1.2 1,1′-methylene-bis-(3-mesityl-imidazol-2-ylidene) Lmes
(LmesH2)Br2 (1.50 g, 2.75 mmol) was weighed out into a Schlenk and suspended in ether (30 ml). In a separate Schlenk, KN(SiMe3)2 (1.20 g, 6.05 mmol) was dissolved in diethyl ether (20 ml). The solution of KN(SiMe3)2 was cooled to –78 °C and added portionwise with efficient stirring to the suspension of the salt at the same temperature. After completion of the addition, the mixture was stirred at –78 °C for 1 h and allowed to warm to –20 °C slowly over 2 h and stirred at this temperature for 30 min. The solution was filtered through a pad of Celite (2 cm) into a Schlenk that was kept at –78 °C. The pad was washed with pre-cooled diethyl ether until the washings were not colored (2 × 30 ml). The combined washings were concentrated under reduced pressure to ca. 1/3 of the original volume and the solution was cooled at –35 °C affording a yellow solid that was isolated by decanting the mother liquor with a cannula and washed with petrol (30 ml) and dried under vacuum. Yield: 0.62 g, 60.5%. NMR (C6D6): 1H, δH 2.10 (12H, s, o-CH3), 2.20 (6H, s, p-CH3), 6.30 (2H, s, CH2), 6.40 (2H, s, backbone imidazol-2-ylidene), 6.80 (4H, s, mesityl aromatic-H), 7.20 (2H, s, backbone imidazol-2-ylidene). 13C{1H}: δC, 17.9, 20.9 (mesityl-CH3), 65.7 (-CH2-), 118.1, 121.7 (4,5-imidazol-2-ylidene), 129.0, 135.3, 137.3, 138.9 (aromatic), 218.0 (imidazol-2-ylidene). The solid can be stored at –35 °C under nitrogen without decomposition. X-ray quality crystals were obtained by prolonged cooling of ether solutions at –35 °C.
4.1.3 Preparation of LDiPPS2
Oven dried sulphur (0.02 g, 0.64 mmol) in THF (20 ml) was added to LDiPP (0.15 g, 0.32 mmol) in THF (30 ml) at RT. The mixture was stirred for 72 h to give a pale orange solution. The THF was evaporated under reduced pressure, the solid residue was dissolved in ether (30 ml) and layered with petrol (30 ml). The pale orange solid precipitate was collected and dried under vacuum. NMR (C6D6): 1H, δH 0.90 and 1.20 (d, 2 × 12H, (CH3)2CH), 2.50 (sept, 4H, (CH3)2CH), 5.80 (s, 2H, backbone imidazol-2-ylidene), 6.00 (s, 2H, methylene bridge), 7.00 (doublet, 4H, aromatic DiPP), 7.10 (triplet, 2H, arom. DiPP), 7.50 (s, 2H, backbone imidazol-2-ylidene). 13C{1H}: δC 22.3 and 22.9 ((CH3)2CH), 27.5 ((CH3)2CH), 54.6 (CH2 bridge), 116.6 and 117.4 (imidazol-2-ylidene backbone), 123.0, 128.9, 132.9 and 145.4 (aromatic), 180.3 (C = S). Anal. Calcd for C31H40N4S2 (%): C, 69.88; H 7.57; N 10.52; found (%): C, 69.78; H, 7.64; N, 10.43.
4.1.4 Preparation of LDiPPSe2
Dried selenium (0.05 g, 0.64 mmol) in THF (20 ml) was added to a stirred solution of LDiPP (0.15 g, 0.32 mmol) in THF (30 ml) at RT. The mixture was stirred at RT for 72 h to giving a pale green/brown solution. The volatiles were removed under reduced pressure and the solid residue dissolved in ether (30 ml). Small amounts of black precipitate were removed by filtration and the filtrate evaporated to dryness giving a dark orange solid. NMR (C6D6): 1H, δH 0.90 and 1.20 (2 d, 24H, (CH3)2CH), 2.40 (sept, 4H, (CH3)2CH), 5.90 [(s, 2H, imidazol-2-ylidene), 6.30 (s, 2H, CH2 bridge), 7.00 (d, 4H, aromatic), 7.10 (t, 2H, aromatic)], 8.00 (s, 2H, imidazol-2-ylidene). 13C{1H}: δC, 22.3 and 23.0 ((CH3)2CH), 27.7 ((CH3)2CH), 57.9 (CH2 bridge), 118.8 and 119.4 (backbone imidazol-2-ylidene), 123.0, 129.0, 133.5 and 145.0 (aromatic), 161.3 (C = Se). Anal. Calcd for C31H40N4Se2 (%): C, 59.42; H 6.43; N 8.94; found (%): C, 58.22; H, 7.13; N, 8.72.
4.1.5 Preparation of LDiPPTe2
Tellurium (0.08 g, 0.64 mmol) in THF (20 ml) was added to a stirred solution of LDiPP (0.15 g, 0.32 mmol) in THF (30 ml) at RT. After 72 h, a brown solution was obtained. The THF was removed under vacuum and the solid residue was dissolved in diethyl ether (30 ml). Some black precipitate formed on addition of ether was removed by filtration. The filtrate was layered with petrol to give yellow brown crystals. NMR (C6D6): 1H, δH, 0.80 and 1.30 (two d, 24H, (CH3)2CH), 2.30 (sept, 4H, (CH3)2CH), 6.10 (s, 2H, imidazol-2-ylidene), 6.40 (s, 2H, methylene bridge protons), 7.00 (d, 4H, aromatic), 7.10 (t, 2H, aromatic), 8.6 (s, 2H, imidazol-2-ylidene). 13C{1H}: δC, 22.1 and 23.3 ((CH3)2CH), 27.9 ((CH3)2CH), 64.0 (CH2 bridge), 121.3 and 121.4 (imidazol-2-ylidene), 123.2, 129.3, 133.5 and 144.7 (aromatic). C = Te was not observed. Anal. Calcd for C31H40N4Te2 (%): C, 55.43; H 5.57; N 7.74; found (%): C, 55.39; H, 5.66; N, 7.85. X-ray quality crystals were obtained by layering a C6D6 solution with petrol in an NMR tube.
4.1.6 Synthesis of [PdLDiPPMe2] (1)
To a solution of [Pd(tmeda)Me2] (0.10 g, 0.39 mmol) in diethyl ether at –78 °C, was added by cannula a solution of LDiPP (0.18 g, 0.39 mmol) in the same solvent. Upon completion of the addition, the colour had changed from light to intense yellow. The solution was allowed to warm to room temperature overnight becoming brown-red. Evaporation of the solvent under reduced pressure left a dark green-purple solid, which was dissolved in THF and layered with petrol to give colorless crystals. NMR (acetone-d6): 1H, δH –1.00 (s, 6H, Pd-(CH3)2), 0.90 (d, 12H, (CH3)2CH), 1.10 (d, 12H, (CH3)2CH), 1.60 (m, 4H, THF), 2.60 (sept, 4H, (CH3)2CH), 6.15 (s, 2H, CH2 bridge), 6.85 (s, 2H, NHC backbone), 7.10 (d, 4H, DiPP), 7.20 (d, 2H, DiPP), 7.40 (s, 2H, NHC backbone). 13C{1H}: δC –3.8 [Pd-(CH3)2], 23.8 ((CH3)2CH on Dipp), 25.6 ((CH3)2CH), 55.0 ((CH3)2CH), 70.0 (CH2 bridge), 120.0 (imidazol-2-ylidene), 123.8 (imidazol-2-ylidene backbone), 125.0 (C = C backbone), 126.3 (aromatic of DiPP), 130.0 (aromatic of DiPP), 146.3 (aromatic of DiPP), 212.0 (CNHC). Anal. Calcd. for C33H48N4Pd.THF (%): C, 65.60; H 8.30; found (%): C, 65.62; H, 8.35.
4.1.7 Synthesis of [PtLDiPPMe2] (2)
To a solution of [(Pt(μ-SMe2)2Me2]2 (0.04 g, 0.07 mmol) in diethyl ether at –78 °C, was added by cannula a solution of LDiPP (0.07 g, 0.14 mmol) in the same solvent. After stirring for 72 h the volatiles were removed under reduced pressure to give a black solid residue which was washed with pentane and ether and dissolved in THF giving a purple solution which on concentration and standing at room temperature overnight gave colorless crystals. More crystals could be obtained from the supernatant by layering it with petrol. NMR (acetone-d6): 1H, δH -0.10 (t, 6H, (CH3)2-Pt satellites), 1.25 (d, 12H, (CH3)2CH), 1.50 (doublet, 12H, (CH3)2CH), 2.00 (m, 4H, THF), 3.05 (sept, 4H, (CH3)2CH), 3.85 (4H, m, THF), 6.30 (s, 2H, CH2 bridge), 7.20 (s, 2H, NHC backbone), 7.40 (d, 4H, aromatic DiPP), 7.55 (d, 2H, aromatic DiPP), 7.70 (s, 2H, NHC backbone). Anal. Calcd. for C33H48N4Pt·THF (%): C, 57.90; H 7.30; N, 7.29; found (%): C, 57.93; H, 7.00; 7.19.
4.1.8 Synthesis of [IrLDiPP(1,5-COD)]PF6 (3)
A solution of LDiPP (0.11 g, 0.24 mmol) in THF (20 ml) was added at –78 °C to a solution of [Ir(1,5-COD)(μ-Cl)]2 (0.08 g, 0.12 mmol) in the same solvent (10 ml). After the addition the cooling bath was removed and the orange reaction mixture was allowed to reach room temperature, when it became brown. A suspension of KPF6 (0.02 g, 0.12 mmol) in THF (20 ml) was then added to the reaction mixture and the whole was stirred at room temperature overnight. After evaporation of the volatiles under reduced pressure, the solid residue was washed with petrol (2 × 15 ml) and toluene (15 ml) and crystallised from THF/petrol affording dark red crystals. NMR (acetone-d6): 1H, δH 7.95 (d, 2H, NCHCHN), 7.66 (d, 2H, NCHCHN), 7.50–7.60 (m, 2H, DiPP aromatic), 7.35–7.50 (m, 4H aromatic DiPP), 6.68 (d, 1H, CH2 bridge), 6.52 (d, 1H, CH2 bridge), 4.29 (br s, 4H, COD vinyl), 3.58 (m, THF), 3.20 (br s, 8H, COD allyl), 2.84 (sept, CH(CH3)2), 2.24 (sept, CH(CH3)2), 1.48 (d, 3H, CH(CH3)2), 1.39 (d, 3H, CH(CH3)2), 1.11 (d, 3H, CH(CH3)2), 0.98 ppm (d, 3H, CH(CH3)2); 13C{1H}: δC 172.7 (NCN), 136.4, 131.5, 127.3, 125.2, 121.5 (aromatic DiPP), 73.2 (COD vinyl), 68.1 (CH2 bridge), 63.9 (iPr CH), 31.8, 26.2 (iPr CH3) ppm; 19F NMR: –72.4 (d). Anal. Calcd. for C39H43F6IrN4P (%): C, 51.76; H, 4.79; N, 6.19; found: C, 51.66; H, 4.77; N, 6.16.
4.1.9 Preparation of [NiLDiPPBr2] (4)
LDiPP (0.15 g, 0.32 mmol) in THF (30 ml) was added at –78 °C with stirring to [NiBr2(dme)] (0.10 g, 0.32 mmol) in THF (30 ml). Stirring at –78 °C was continued for 10 min and then the mixture was allowed to warm to room temperature when it became dark orange. The volatiles were removed under reduced pressure to give a pink solid, which was insoluble in inert solvents but sparingly soluble in THF. X-ray quality crystals were obtained by dissolving a small amount in THF (30 ml) and layering with diethyl ether.
4.1.10 Preparation of [NiLDiPPBr2] (4) by generating the LDiPP in situ
KN(SiMe3)2 (2.40 g, 12.00 mmol) in diethyl ether (100 ml) was added at –78 °C portionwise with rapid stirring to (LDiPPH2)Br2 (3.00 g, 4.80 mmol) in diethyl ether (100 ml). This was followed by addition at the same temperature of [NiBr2(dme)] (0.11 g, 3.70 mmol, equimolar amount based on 75% carbene yield) in THF (100 ml). Cold THF (200 ml at –78 °C) was used to dilute the reaction mixture. The mixture was allowed to warm to room temperature and then stirred overnight. A brown suspension with some pink precipitate was observed. The mixture was filtered on a glass sinter and washed with degassed H2O (30 ml) followed by EtOH (30 ml) and then Et2O (50 ml). The dark pink solid was dried under vacuum. Anal. Calcd. for C31H40N4Br2Ni (%): C, 54.18; H, 5.87; N, 8.15; found: C, 54.01, H, 5.74; N, 8.03. The product is paramagnetic giving featureless NMR spectra in THF-d8.
4.1.11 Formation of [NiLDiPP(CO)2] (5)
In a Fisher-Porter bottle, to a solution of [NiLDiPPBr2] (0.04 g, 0.06 mmol) in THF (10 ml) was added Na/Hg (1.00 g of 0.4% w/w, excess), the mixture was pressurised with CO (100 psi), and stirred at room temperature for 12 h. After releasing of the pressure the solution was decanted from the Hg pool and the THF removed under reduced pressure. The residue was dissolved in ether, filtered, the filtrate concentrated and cooled (4 °C) to give small quantity of yellow crystals that were characterised crystallographically.
4.1.12 X-ray crystallography
The data sets for (LDiPPH2)(OTf)2 and complexes 2, 3 and 5 were collected on a Enraf-Nonius Kappa CCD area detector diffractometer with an FR591 rotating anode (Mo Kα radiation) and an Oxford Cryosystems low-temperature device, operating in ω scanning mode with ψ and ω scans to fill the Ewald sphere. The crystals were mounted on a glass fiber with silicon or fluorocarbon grease, from Fomblin vacuum oil. The programs used for control and integration were Collect, Scalepack, and Denzo [16]. All solutions and refinements were performed using the WinGX [17] package and all software packages within. All non-hydrogen atoms were refined using anisotropic thermal parameters, and hydrogens were added using a riding model. Complexes 1, 2, 3 and 5 contain one THF solvent molecule of crystallization in the asymmetric unit. In the structures of (LDiPPH2)(OTf)2 and 3 one of the isopropylphenyl groups was disordered over two positions that were refined anisotropically without any restraints. The structure of 1 contains one THF solvent molecule of crystallization which was disordered over two positions and refined anisotropically. The crystals of Lmes, LDiPPTe2 and of the complexes 1 and 4 were very small, and the data sets were collected at the synchrotron facility at Darebury, UK [18]. Crystal data for all structurally characterised compounds are given in Table 1.
X-ray data collection and refinement parameters for compounds (LDiPPH2)(OTf)2, Lmes, LDiPPTe2 and complexes 1–5.
(LDiPPH2)(OTf)2 | Lmes | LDiPPTe2 | 1 | 2 | 3 | 4 | 5 | |
Chemical formula | C33H42F6N4O6S2 | C25H28N4 | C37H40D6N4Te2 | C37H54N4OPd | C37H54N4OPt | C39H52IrN4P F6C4H8O | C31H40Br2N4Ni | C37H48N4Ni O3 |
CCDC number | 906016 | 906017 | 906018 | 906019 | 906020 | 906021 | 906022 | 906023 |
Formula mass | 768.83 | 384.5 | 808.01 | 2708.97 | 765.93 | 986.12 | 687.20 | 655.50 |
Crystal system | Monoclinic | Monoclinic | Monoclinic | Orthorhombic | Orthorhombic | Orthorhombic | Orthorhombic | Monoclinic |
a/Å | 15.6001(11) | 8.030(3) | 12.1082(10) | 9.2015(18) | 9.16850(10) | 13.6258(4) | 12.6116(13) | 10.4866(3) |
b/Å | 24.6198(11) | 9.795(3) | 16.4200(13) | 18.932(4) | 18.9619(2) | 24.9908(7) | 14.5499(15) | 17.4528(4) |
c/Å | 9.9798(4) | 28.373(10) | 18.3694(15) | 19.892(4) | 19.9278(2) | 25.1385(4) | 16.8485(17) | 19.3943(6) |
α/̊ | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 |
β/̊ | 103.562(4) | 97.544(3) | 99.721(2) | 90.00 | 90.00 | 90.00 | 90.00 | 104.482(1) |
γ/̊ | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 | 90.00 |
Volume/Å3 | 3726.1(4) | 2212.3(13) | 3599.7(5) | 3465.2(12) | 3464.49(6) | 8560.2(4) | 3091.7(5) | 3436.77(16) |
Temp/K | 120(2) | 120(2) | 120(2) | 120(2) | 120(2) | 153(2) | 120(2) | 120(2) |
Space group | C2/c | P 21/c | P21/c | P212121 | P212121 | Pbca | P212121 | P21/n |
Z | 4 | 4 | 4 | 4 | 4 | 8 | 4 | 4 |
μ/mm−1 | 0.220 | 0.069 | 1.650 | – | 0.9228 | 0.597 | 3.238 | 0.605 |
Reflections measured | 26333 | 21165 | 57802 | 36753 | 30465 | 67631 | 18813 | 44020 |
Independent reflections | 3291 | 6380 | 8380 | 10304 | 7809 | 8381 | 4280 | 7853 |
Rint | 0.1010 | 0.0524 | 0.0671 | 0.0449 | 0.0450 | 0.0459 | 0.0477 | 0.0836 |
Final R1 values (I > 2σ(I)) | 0.2005 | 0.0539 | 0.0508 | 0.0309 | 0.0306 | 0.0734 | 0.0401 | 0.0482 |
Final wR(F2) values (I > 2σ(I)) | 0.1217 | 0.1502 | 0.1038 | 0.0695 | 0.0609 | 0.1155 | 0.0974 | 0.0946 |
Final R1 values (all data) | 0.2101 | 0.0625 | 0.0684 | 0.0331 | 0.0348 | 0.0459 | 0.0401 | 0.0823 |
Final wR(F2) values (all data) | 0.2101 | 0.1601 | 0.1143 | 0.0711 | 0.0628 | 0.0734 | 0.1016 | 0.1070 |
Goodness of fit on F2 | 1.216 | 1.035 | 1.104 | 1.019 | 1.130 | 1.046 | 1.070 | 1.037 |
Acknowledgements
We thank CNRS for a fellowship (to AAD). AAD is also grateful to the Région Alsace, the Département du Bas-Rhin and the Communauté urbaine de Strasbourg for the award of a Gutenberg Excellence Chair (2010–2011). We also thank Dr Pierre Braunstein for support and fruitful discussions and Dr Mark E. Light, Dr Simon J. Coles (University of Southampton) and Dr Pierre de Fremont (Laboratoire de chimie de coordination, UMR 7177) for the data collection of Lmes and 4 and assistance in structure solution and refinement, respectively.